What Is A 315 Spray Tip Used For?

What is the best spray tip for latex paint?

Recommended Tip Sizes For Common Coating MaterialsLaquer or Stain.009 – .013Oil Based Paint.013 – .015Latex Paint.015 – .019Heavy Latex or Smooth Elastomeric.021 – .025Elastomeric & Blockfiller.025 – .035 +.

What size tip should I use to spray primer?

A general rule of thumb is: Heavy-bodied primers and primer surfacers work best when you use a nozzle size of 1.7 to 2.2. Basecoats should be sprayed with a 1.4 to 1.6 nozzle.

Are Graco and Titan tips interchangeable?

Amazon.com: Customer Questions & Answers. This only fits Graco RAC X tip guards but Graco tip guards will fit Titan guns. The tips alone aren’t interchangeable within the different guards though.

Why is my spray tip spitting?

Spray guns spit when air is being introduced into the fluid outside of at the air cap. … A loose fluid nozzle does not properly seat in the tip of the spray gun and causes air to enter the fluid supply resulting in spitting.

Is it better to spray or roll interior doors?

Whether you spray, brush or roll, you’ll get the best results if you prepare the door properly, and, because paint levels better on a horizontal surface, if you take the door down and lay it flat. Even if you have to paint the door in place, you can still get good results.

Do I need to back roll after spraying primer?

Conclusion. Typically, back rolling after spraying on walls and ceilings is ideal especially for your primer. It will help in promoting better adhesion of the primer and reduce issues of raised filaments with drywall.

Can you use a spray paint gun on interior walls?

You can spray paint interior walls if you like speed, and outdoors too. You can complete some jobs much faster than other methods available by using a paint sprayer. … It’s ideal for your garage or a large outdoor wall if you need it done quickly and with a professional finish.

Is it better to spray or roll ceiling?

To Spray or Roll? Some painters break out a roller when it’s time to paint a ceiling, but it isn’t always the best tool for the job. If you’re planning on painting the entire room, a paint sprayer is much more efficient, especially if the ceiling is heavily textured.

Why is my paint sprayer leaving lines?

The main causes of streaks and disturbances in the spray pattern when using Airless devices are: Pressure set too low. Nozzle worn. Material supply disrupted (eg clogged filters)

Do you spray ceilings or walls first?

Spray Painting both the Walls and Ceiling Spray the walls before the ceiling. Allow the wall paint to fully dry, cover the walls with tape and plastic, and spray the ceiling. Masking walls is a lot easier than masking a ceiling upside down, if you were to spray the ceiling before the walls.

What tip to use for spraying doors?

The best tip to use for spraying interior doors with an airless sprayer is a 310, or a 312 tip. These tips produce a 6-inch spray fan to coat doors quickly with less overlapping than using a smaller tip.

What does a .517 tip mean?

“The 3 numbers used to describe a tip size, example 517, refers to the fan size and the orifice size. The fan size of a 517 is 10 inches wide, one foot from the surface being sprayed. The first number is always ½ the actual fan width. The last 2 numbers refer to the actual size of the orifice.

Is it worth buying a paint sprayer?

Running out of paint while spraying covered the surface with uneven globs. … As long as you’re into taping sheets of plastic on the walls and you’ve got a bottomless budget for paint, a sprayer is worth considering. It has its strong points, but it’s not a truly practical replacement for the old brush and roller.

What tip do you use for an airless sprayer?

Choosing an Airless Tip Size Based on Material to be SprayedVarnishes (before low VOC)*.009thin materialsEnamels – oil-base.013mediumLatex paint – interior.013Latex paint – exterior.015Primers – latex.01516 more rows

What is a 311 spray tip used for?

6 inch spray pattern ideal for narrow surfaces such as fences, decks and furniture. The . 011 inch hole size optimal for spraying thinner materials like semi transparent stains, water sealers, stains or polyurethanes. Less overspray shortens cleanup time with less wasted material.