- Does kydex scratch gun finish?
- What is the difference between kydex T and kydex V?
- Does Cerakote wear off?
- Can you reshape kydex?
- Are leather holsters bad for guns?
- Which is better leather or kydex?
- Why is kydex so expensive?
- Is Cerakote permanent?
- Can you heat kydex in the oven?
- Do Kydex holsters scratch your gun?
- At what temperature does kydex soften?
- How hot does kydex need to be to mold?
- Does Cerakote rub off?
- Can you heat kydex with a hair dryer?
- Does Cerakote scratch easily?
- Is kydex bad for guns?
- How tight should kydex holster be?
- Will hot kydex hurt my gun?
- Is kydex comfortable?
- How durable is kydex?
- Does kydex break?
Does kydex scratch gun finish?
To give a more direct answer to your question, ALL HOLSTERS, no matter who made them, how much they cost, or what they’re made of will wear your guns finish.
Kydex will rather quickly wear the finish, but only on the areas where the holster is molded to actually contact the gun..
What is the difference between kydex T and kydex V?
recognized for UL Std 94 V-0, 5V and has 961 J/m (18 ft-lbs/in) Notched Izod impact resistance. KYDEX® T– High impact fire-rated sheet that is less hygroscopic and usually does not require pre-drying. … KYDEX® V– Cost-competitive, recycled-grade utility sheet offered only in the color black.
Does Cerakote wear off?
All coatings and bluing will wear off. For the builders that use Cerakote often, how are they wearing overtime in heavy use firearms? !
Can you reshape kydex?
If it is true Kydex and you don’t over heat it, yes it can be heated and reshaped. Temper this with the warning that the material on the inside is a wild card. If it is true Kydex and you don’t over heat it, yes it can be heated and reshaped.
Are leather holsters bad for guns?
Although there are some really nice looking leather options for concealed carry, they can be dangerous to use. Over time and use leather becomes softer and more pliable. When you draw your gun from the holster the leather at the top will tend to collapse, making it difficult and dangerous to re-holster your pistol.
Which is better leather or kydex?
Leather holsters are more comfortable, long-lasting, aesthetically pleasing, and protect the firearm very well. However, they require maintenance, have leaner retention, and are costly. … But Kydex holsters offer limited comfort, are a bit noisy, and might damage the polish of your weapon.
Why is kydex so expensive?
The material in a kydex holster probably isn’t more than a buck or two – the tooling is the biggest cost. I believe that all politicians are born with a genetic flaw that compels them to meddle in the affairs of others. Molds are expensive. VERY expensive.
Is Cerakote permanent?
Cerakote is an oven cured, thin film ceramic gun coating that is rust-proof, self-lubricating, scratch-resistant, and solvent resistant. Cerakote is a permanent ceramic finish that is designed to last the lifetime of the firearm. …
Can you heat kydex in the oven?
Preheat oven around 330 deg. put your Kydex in the oven on top of a rock, watch it go limp.. if you got no thermometer just pick it up and if it`s limp like a spaghetti …it`s done…
Do Kydex holsters scratch your gun?
KYDEX lasts longer than cheaper plastic and it’s far less likely to damage your firearm, no matter how many times you holster and un-holster your gun.
At what temperature does kydex soften?
between 305 and 320Fhoopster. Like Justin said, between 305 and 320F is a good temp for kydex. If you just want to loosen one up that’s too tight, another method would be to use a heat gun or hot hair dryer and warm it with the knife in place. Just go slowly.
How hot does kydex need to be to mold?
182 – 196°C (360 – 385°F) for 1.50mm – 3.20mm (0.060” to 0.125”). 65.5ºC (150ºF) before removing the part from the mold. If you are using a temperature controlled mold, maintain a mold temperature of 65.5ºC (150ºF) in the cooling cycle • Do Not exceed 71.1ºC (160ºF).
Does Cerakote rub off?
No it’s not normal to rub off with your thumb. I spray a lot of it and it’s tough stuff. Sounds like not enough hardener or its not Cerakote. Even the c-series would hold up to thumb rubbing.
Can you heat kydex with a hair dryer?
A hair dryer is not hot enough, you will need to heat Kydex to 300F+, which means a heat gun. Just be careful not to melt the plastic completely. Keep the heat gun moving, don’t let it stay in one spot. … Hair dryer works fine.
Does Cerakote scratch easily?
I have had Cerakote scratch off. Well, they say it isn’t paint, but it is paint. Of course paint can be scratched off, and like any paint it adds a measurable thickness where applied, so it shouldn’t be applied everywhere.
Is kydex bad for guns?
A properly formed Kydex holster will not wear your firearm. The inside of a Kydex holster is totally smooth. What wears on a firearm is the dirt, dust, debris, etc. that gets stuck in your holster.
How tight should kydex holster be?
The tension screws should hold the gun in the holster snug, but should come loose with a fair shake. (Test this with an UNLOADED firearm only.) For an Outside the Waistband holster, tension should hold the firearm snugly in the holster. A firm shake should release the firearm from the holster.
Will hot kydex hurt my gun?
Anything over 350 and the kydex gets a sheen to it. From what I’ve seen, 350 is the sweet spot. I’ve used one gun a few times as the mold. Hasn’t hurt the finish at all, and the gun doesn’t seem to get horribly hot, even after 10-15 minutes in the press.
Is kydex comfortable?
Kydex is made in thin sheets that can be heated up and then molded around a gun or a replica to perfectly fit all of the nooks and crannies. … One of the main complaints about Kydex holsters is the comfort factor. While rigidity is a good thing when it comes to keeping the gun in its place, it is a bad thing for comfort.
How durable is kydex?
Relatively hard thermoplastic, with a hardness of 90 on the Rockwell R scale. This hardness, combined with a grained surface, increases its abrasion resistance.
Does kydex break?
Kydex isn’t going to stretch for you. The only way in which Kydex will “break in” is that it will sort of polish on the retentive contact points, over many presentations, so that the draw will become smoother, but the retention won’t loosen.