How Much Does It Cost To Stain A Deck Yourself?

Can I stain my own deck?

Unless the deck is entirely new, you’ll need to clean the surface and allow a day to dry before staining.

Stain needs time to absorb into the wood but dries quickly, so avoid applying the stain in direct sunlight.

Match the stain to your deck’s type of wood..

What happens if you don’t seal stained wood?

A: If you don’t apply some kind of sealer the wood will be dried-out and lifeless. … The final step in staining wood is to wipe off any excess, so the process leaves nothing behind. A finish is typically applied after a piece has already been stained and is normally applied with a paintbrush.

What happens if it rains before deck stain dries?

If it rains within 48 hours after you apply the stain, the water will soak into the wood pores and try to displace the stain. This will result in a splotchy surface rather than an even tone. If it rains right after you apply the stain, the stain will peel and flake off.

Should I pressure wash my deck?

A pressure washer can clean a wood deck much faster than you can scrub it by hand. That is a terrific advantage. However, a pressure washer will frequently destroy the surface of the wood. The stream of water can be powerful enough to erode the light-colored spring wood fibers.

How much does it cost to stain a deck and railing?

The average cost to stain deck railings, handrails, and spindles are $4 to $8 per linear foot without stripping the wood, and between $10 and $14 per linear foot when stripping is included. It’s not necessary to have the railings stained as often, as they remain in good condition longer than the planks.

What is the best way to stain a deck?

Apply painter’s tape to any nearby surfaces — such as siding — that you need to protect. Apply the deck stain with a natural bristle brush. A roller gets the job done faster, but brushing helps force the stain into open grain and pores. It’s especially important to work stain into butt joints where two boards meet.

Can I use a roller to stain my deck?

A paint roller can be used to roll stain on. … A wide 18-inch roller may work well for staining a few fence or deck boards at a time but a mop or stain pad will hold more stain lessening the amount of time you have to dip back into the stain bucket.

Should you pressure wash deck before staining?

Pressure washing can help, but if you want your stain to last, using a good deck cleaner and brightener on the deck prior to pressure washing will provide you the best result. A good deck cleaner can remove the gray fibers, dirt, mold, mildew and other impurities deep in the wood.

How many coats of deck stain should I use?

The general rule of thumb is to apply only as much deck stain as the wood can absorb. Typically this will be 2 coats, unless your dealing with extremely dense hardwoods which may only be able to absorb 1 coat of wood stain.

What happens if you stain over stain?

If the stain that you are replacing is darker than the new stain, then yes, you will need to remove the old stain. If you are going to restain it the same or a darker color, then you don’t need to worry too much as the previous stain won’t be visible once the job is done.

What lasts longer deck stain or paint?

On average, decks need to be stained again every other year. A quality, professional paint job will last longer than a quality, professional deck staining. However, an oil-based semitransparent stain can last for three to five years.

Is it cheaper to paint or stain a deck?

Stain is more budget-friendly. Stain runs between $20 and $35 per gallon, while exterior paint suitable for decking ranges from $30 to as much as $60 per gallon. Plus, if painting, you’ll have to factor in an extra $15 to $40 per gallon of wood preservative and $15 to $30 per gallon of primer.

Is it better to seal or stain a deck?

The advantage of this, they say, is the sealer provides additional protection against water and weather damage, while the stain helps reduce fading from UV rays. Sealers should last at least a year, with some lasting up to three years.

Can I leave my deck untreated?

It may be many years before an untreated deck becomes completely unusable. However, a deck that is properly sealed and maintained with a yearly maintenance program consistently outlive a deck that is left to its own devices by a significant margin.

Can I put Thompsons Water Seal over stain?

And actually, the answer is YES—you can use our EMTECH water-based sealer or top coat over the oil stain. The beauty of all our water-based sealers and topcoats is that they’ll level and adhere to whatever solvent- or oil-based stain you’ve used.

Can I paint over stain without sanding?

Painting Over Stained Wood Paint will adhere to stain, but it won’t adhere to the shiny coat of varnish or lacquer that is often applied over the stain. To paint over stained wood you have to remove the varnish with either sandpaper or a deglosser. … Follow up with a couple coats of paint and you’re done!

How much should I pay to have my deck stained?

The cost to stain your deck typically ranges from $540 to $1,050 with an average of just over $700. This equates to an average cost of $2 to $4 per square foot for labor and materials. Higher-quality stains will run up the price, as will washing or sealing the wood prior to staining.

Should I use a brush or roller to stain my deck?

You should use a roller brush or sprayer to apply a steady coat of quality stain, such as Olympic Elite stains or Olympic MAXIMUM stains. If you see that too much wood stain has been used in an area, use a roller or brush to fix the imperfections.